仅供个人参考
插板阀是综合多年来使用插板阀的经验具创新的设计，主要用于通风除尘、风力输送及排风系统管路上的调节和固体粉料输送的调节和切断。
This series valve is the most innovative design basing on the experience of using inserting disc valve. It is mainly used to regulate in pipes of venting removing dust, carrying, venting system and to regulate or cutting carrying of solid powder.
结构特点：
Structure characteristic:
采用优质钢材焊接而成，具有结构简单，操作自如，阀板滑动灵活，密闭性能优良等特点。特别是局部阻力损失小，调节性能好，维护保养拆卸方便，不易变形，克服了老式插板阀漏风大、变形快、调节困难的毛病。特别适用于无粘度的固体粉料及小于Ф10mm颗粒料、晶体料、固状物料的输送。
This valve is welded in fine steel and simple in structure, handy to operate, smooth to slide, good in seal. Especially it is less loss in local resistance, good regulation, convenient to replace and maintain, not distorted. It overcomes the defect of outdated inserting disc valve such as great leakage, distorting quickly and difficulty in regulating. It is suitable to transport non-glutinosity solid powder and grain, crystalloid, solid material less than 10mm.
性能参数：
Performance parameter:
公称压力 Nominal pressure | 介质流速 Medium velocity | 适用温度 Suitable temperature | 适用介质 Suitable medium |
0.05MPa | ≤28m/s | ≤300℃ | 空气、粉尘气体、无粘度固体粉料、晶体料 Air, gas with dust, non-glutinosity solid powder, crystalloid |
工作原理：
Working principle:
插板阀主要由执行机构、阀体、插板、密封装置、行程开关等部件组成。运行时输出指令（电源或气源）给执行机构，由执行机构带动插板向外抽出，达到工况需要位置，撞动行程开关停止，由行程开关反馈信号（开关信号）给控制室。反之则关闭插板阀（向内推进）。
The valve is mainly made up of actuator, body, disc, seal device and journey switch etc. Instruction is transmitted to the actuator. The actuator drives disc draw out to reach the requiring position and then bumps the journey switch to stop. Journey switch feeds back the signal to control room. Otherwise close disc.
使用说明：
Operation instruction:
l 本阀连接方式为法兰连接。
l 本阀可水平或垂直安装，安装时两法兰联接中间必须加密封垫片，然后均匀锁紧螺栓。
l 手动操作时向外抽出为开，向内推进为关。不得在把手上增加辅助器材。
l 执行机构应按其使用说明正确接线与操作。
l 若长期存放应使设备处于关闭状态，各传动部位应加润滑油，不允许露天存放或堆置。
l Joint type of this valve is flange joint.
l The valve can be installed in horizontal or vertical. Add seal cushion between two flanges connection and screw down bolt.
l Draw out handle means open and push in means close. Assistant lever can’t be added to handle.
l Actuator must be connected and operated exactly according to the operation instruction.
l Add lubricant to transmission part when valve is long stored. It should not be placed or piled up in the open air.
D QSFC--- Ⅰ Ⅱ外形连接尺寸：
Appearance joint dimension:
传动装置参数：
Transmission device parameter:
规 格 Type | 200~300 | 320~560 | 600~700 |
电动推杆 Electric draw stem | DTⅠA63-M P：0.06KW | DTⅡA100-M P：0.25KW | DTⅡA250-M P：0.37KW |
气动推杆 Pneumatic draw stem | 10A-5LA50B | 10A-5LA63B | 10A-5LA80B |